[Mountain Bike]: Bar End key equipment should not be overlooked

Bar End key equipment should not be overlooked

Bar End devices that many people may overlook, but many might see as important. Is a device mounted on the tip of the hand. Sometimes be viewed as an option to add beauty to your car is good, some cars do not put put some cars then why not put people to wear what would be helpful. I would say that of course useful. If known to be used because the mountain bike. Use hands to press the weight straight to hand over a raised hand. And a position in the hand is only a single location. When we are cycling a long distance (some spin to have symptoms long ago) to the fatigue at the back or tea at hand if we do not change. What hand position. Putting bar end is held in the hand placements to increase hold hands. We can change the posture of the body and hold hands.

                Bar end will benefit both in the flat and steep. A position to grasp the difference. On the other hand holding the flat of the hand line will be aligned with a hands-on. Stretch arm will squat down under the body does not make a lot less. Hold the end of the bar along the palm of the hand set to allow arms to the side. Fried body to fall forward into more flexible than the shoulder movement. Arms, chest compression does not allow more spontaneous respiration with When we stand on the rock, whether horizontal or the slope to catch the bar end will help us Have more pressure because we are lifted higher than the hands and also to handle the. More established. It seemed to capture different. Weight will be taken to the front to reduce friction on the rear wheel spinning ride. Up the slope to catch the bar end will help bring forward new weight by pulling the bar end.

                Choice in terms of size, length and shape depend on surface and fit preferences of each individual. For large hands to use bar-end is a small and research would not be caught right-handed people are not at hand, a small end of the bar is too large, it will not hold steady Should be chosen to fit the palm and grip. Bar-end brands will each have different shapes and sizes out. But at the same bar that is attached to the end of the hand. Both direct perpendicular to the hands. Direct oblique inward and then straight up to the end bent into a different length. The round shape is round. Shaped oval, square wave groove edges, smooth surfaces, it has some designs, depending on the design of each brand. Used to produce materials ranging from steel to aluminum, carbon fiber and rubber to last a lot more soft. For aluminum, there are many colors to choose from. There is also a lightweight carbon fiber does not escape.

                For those who do not have installed bar-end from the beginning. Be viewed as the width of your hand is how much If the old hands who are not cut it, it no problem. Hands are usually wider than shoulder already. If it is hand cut and then to see whether or not long enough. Bar End to eat because of the hand area of ​​approximately 2-3 cm distal to the need to move hand gear Hand brake and the hand into the inner sleeve. Since the middle of a hands-all hands are puffed out, and then gradually reduced by only a hand Over Size is puffed out a lot of hands sliding gear Hand brake and the hand into the sleeve, so there is a limit. So, before you find a bar to try to put end to be able to move hand viewed gear Hand brake and the hand into the sleeve much if you cut their hands using a wide Shoulder was then fixed to recommend changing hands, or hands-off sleeve only. Choosing a cut only if the sleeve length Hand over hand, but must not interfere with. Capture the hand position normally. The hand position can not be narrower than shoulder feared. Because they do not feel right to hold hands and breathing is difficult. In addition, owing to the front of the vehicle difficult to control sensitivity.

                Bar End Installation is easy. Can be done manually. Hand gear only version. Hand brake and the hand into the inner sleeve. Wear bar-end with the hand to the outside edge of the bar end is just the tip of the hand. The bar end at an angle to the ground about 10-45 degrees, depending on preference. The fit and objectives of each individual to be focused on what. To focus on the flat was set to end to the front (at an angle less) If you focus on the uphill slope it end came to the (angle), while not set too because it will cause weight not taken forward. Another important need is not so tight. When we pull or rock may stand to swipe that is sure to hurt. But be careful tightening too specific. It may be the end of the bar legs broken or be broken hand. Most bars will be deducted before the end. Out to be useful and still make it look beautiful too ..